View MAX17061AEVCMAXQU_8927144.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

general description the max17061a evaluation system (ev system) consistsof the max17061a evaluation kit (ev kit) and the maxim cmaxqusb+ command module. windows 2000-, windows xp -, and windows vista -compatible software are also available for use with the ev system(MAX17061AEVCMAXQU+) and can be downloaded from the maxim website ( www.maxim-ic.com/evkitsoftware ). the max17061a ev kit (max17061aevkit+) is a fullyassembled and tested surface-mount pcb that evaluates the high-efficiency max17061a white led (wled) driver. the max17061a ev kit utilizes a step-up dc-dc convert- er to generate the voltage required to drive up to eight strings of 10 surface-mount wleds. the ev kit is pow- ered from dual supplies (v in = 5.5v to 24v and v cc = 4.5v to 5.5v) and can be configured to provide a fixed 25ma or adjustable 15ma to 30ma full-scale led cur-rent. as shipped, the max17061a ev kit is configured for evaluation with four strings of 10 wleds and includes an i 2 c/smbus-compatible interface that allows for soft- ware control of the brightness in 256 steps, backlight- controller operating mode, manufacturer and silicon revision detection, and fault detection.the maxim cmaxqusb+ command module provides the i 2 c/smbus interface and is connected to the computer through the universal serial bus (usb) port. themax17061a ev kit software provides a graphical user interface (gui) for exercising the max17061a features. features ? 7v to 21v input range ? wled drives up to 30ma/string ? drives four strings of 10 wleds (capable ofdriving up to eight strings) ? full-scale led current adjustable from 15ma to30ma, or preset 25ma ? 1mhz pwm switching frequency (selectable:500khz or 750khz, component change required) ? all components < 1.2mm height ? lead(pb)-free and rohs compliant ? fully assembled and tested evaluate: max17061a max17061a evaluation kit/evaluation system ________________________________________________________________ maxim integrated products 1 19-4654; rev 0; 5/09 component lists for pricing, delivery, and ordering information, please contact maxim direct at 1-888-629-4642, or visit maxim? website at www.maxim-ic.com. ordering information part qty description max17061aevkit 1 max17061a ev kit cmaxqusb+ 1 i 2 c/smbus interface command module part type max17061aevkit+ ev kit MAX17061AEVCMAXQU+ ev system windows, windows xp, and windows vista are registered trademarks of microsoft corp. smbus is a trademark of intel corp. + denotes lead(pb)-free and rohs compliant. note: the maxim cmaxqusb+ command module is required when using the max17061a ev kit software. max17061a ev system designation qty description c1 1 0.1? ?0%, 50v x7r ceramiccapacitor (0603) murata grm188r71h104k tdk c1608x7r1h104k c2 1 0.022? ?0%, 50v x7r ceramiccapacitor (0603) murata grm188r71h223k tdk c1608x7r1h223k max17061a ev kit designation qty description c3 1 4.7? ?0%, 25v x5r ceramiccapacitor (1206) murata grm319r61e475k c4 0 not installed, ceramic capacitor(1206) c5, c6 2 1.0? ?0%, 10v x7r ceramiccapacitors (0603) taiyo yuden lmk107bj105ka murata grm188r71a105k c7?12 6 0.33? ?0%, 50v x7r ceramiccapacitors (1206) murata grm319r71h334k tdk c3216jb1h334k c13?20, c22?30 0 not installed, ceramic capacitors(0603) downloaded from: http:///
evaluate: max17061a max17061a evaluation kit/evaluation system 2 _______________________________________________________________________________________ component lists (continued) designation qty description c21 1 220pf ?0%, 50v x7r ceramiccapacitor (0603) murata grm188r71h221k tdk c1608x7r1h221k ccv 0 not installed, test point d1, d82 2 0.7a, 60v schottky diodes (us-flat) toshiba cus04 d2?41 40 white ledsnichia nssw008ct-p1 optek ovsrwacr6 d42?81 0 not installed, white leds j1 1 2 x 10 right-angle receptacle ju1?u4, ju11, ju13 6 3-pin headers ju5?u8 0 not installed, 3-pin headers?hort(pc trace) ju9 1 2-pin header max17061a ev kit (continued) designation qty description l1 1 10?, 1.2a power inductorsumida cr6d09hpnp-100mc tdk vlp6810t-100m1r2 r1 0 not installed, resistor?hort (pctrace) (0603) r2 1 2.21m ?% resistor (0603) r3 1 61.9k ?% resistor (0603) r4 1 130k ?% resistor (0603) r5 1 200k multiturn potentiometer r6 1 41.2k ?% resistor (0603) r7 1 500k multiturn potentiometer r8, r9 0 not installed, resistors (0603) r10 1 5.1k ?% resistor (0603) r11 1 1m resistor (0603) u1 1 wled driver (28 thin qfn)maxim max17061aeti+ 7 shunts ? p c b: m ax 17061a e v alu ation kit+ component suppliers supplier phone website murata electronics north america, inc. 770-436-1300 www.murata-northamerica.com nichia corp. 248-352-6575 www.nichia.com optek technologies 972-323-2200 www.optekinc.com sumida corp. 847-545-6700 www.sumida.com taiyo yuden 800-348-2496 www.t-yuden.com tdk corp. 847-803-6100 www.component.tdk.com toshiba america electronic components, inc. 949-623-2900 www.toshiba.com/taec note: indicate that you are using the max17061a when contacting these component suppliers. downloaded from: http:///
evaluate: max17061a max17061a evaluation kit/evaluation system _______________________________________________________________________________________ 3 quick start recommended equipment max17061a ev system max17061a ev kitmaxim cmaxqusb+ command module (usb cable included) 7v to 21v, 1a power supply (vin) user-supplied windows 2000, windows xp, or windows vista pc available usb port note: in the following sections, software-related items are identified by bolding. text in bold refers to items directly from the ev kit software. text in bold and underlined refers to items from the windows operating system. procedure the max17061a ev kit is fully assembled and tested.follow the steps below to verify board operation. caution: do not turn on the power supply until all connections are completed. 1) on the cmaxqusb+ command module, ensure that the shunt on jumper ju1 is in the 5v (default)position. 2) on the max17061a ev kit, verify that the shunts are installed as follows: ju1?u4, ju13 1-2 ju9 installed ju11 2-3 3) carefully connect the boards by aligning the 20-pin connector of the max17061a ev kit with the 20-pinheader on the cmaxqusb+ interface board. gently press them together. 4) connect the positive terminal of the vin power sup- ply to the vin pad. connect the ground terminal ofthe vin power supply to the pgnd pad. 5) connect the positive terminal of the vcc power supply to the vcc pad. connect the ground termi-nal of the vcc power supply to the gnd pad. 6) connect the usb cable from the computer? type- a usb port to the cmaxqusb+ board? type-busb port. 7) visit www.maxim-ic.com/evkitsoftware to obtain the latest version of the ev kit software, 17061arxx.zip.download and install it on your computer by run- ning the install.exe program. the program files are copied and icons are created in the windows start menu. 8) set the vin power supply to 12v and enable its output. 9) set the vcc power supply to 5v and enable its output. 10) start the max17061a program by opening its icon in the start menu. 11) normal device operation is verified when cmaxqusb hw: connected. max17061a device connected. is displayed at the bottom left of the max17061a ev kit window (figure 1). detailed description of software user-interface panel the program? main window (figure 1) is navigated byusing a mouse or a combination of the keyboard? tab and arrow keys. the max17061a ev kit software pro- vides controls for software-configurable features, such as brightness control , device control , faults/status detection, and manufacturer id and silicon revision detection. changes to the controls result in a writeoperation that updates the appropriate registers of the max17061a. a status box is provided at the bottom of the program? main window and is used to verify com- mand module and device connectivity. a device search option is located under the action menu bar should the user want to switch from demo mode to nor-mal operation. max17061a ev kit files part description install.exe installs the ev kit files on yourcomputer max17061a.exe application program ftd2xx.inf usb device driver file uninst.ini uninstalls the ev kit software usb_driver_help.pdf usb driver installation help file downloaded from: http:///
evaluate: max17061a brightness control and level the max17061a can be configured to one of any 256steps of brightness control. to set the brightness, slide the brightness control track bar to the desired posi- tion, from 0 to 255. the track-bar position is then dis-played in the brightness level group box. device control the max17061a? device control register controls theoperating mode of the backlight controller and backlight on/off states. the max17061a operating mode can be configured according to the bit settings shown in table 1. fault/status detection the max17061a? fault/status read-only register moni-tors the backlight controller? operating state. this regis- ter detects the backlight on/off state, whether one or two led output channels are shut down, overcurrent condi- tions, and thermal faults. when a fault is detected, the corresponding bit is changed from logic 0 to logic 1 and the font color is changed to red. refer to the max17061a ic data sheet for more information regard- ing the fault/status register. manufacturer/silicon revision detection the id register group box provides the manufacturer and silicon revision information for the max17061a ic.this information is read upon initial startup. simple i 2 c/smbus commands there are two methods for communicating with themax17061a, through the normal user interface (figure 1), or through the smbus commands available by selecting the interface diagnostic window menu item max17061a evaluation kit/evaluation system 4 _______________________________________________________________________________________ figure 1. max17061a ev kit software main window table 1. operating modes selected bydevice control register pwm_md pwm_sel operating mode x 1 pwm mode 1 0 smbus mode 0 0 smbus mode with dpst x = don? care. downloaded from: http:///
from the action menu bar. the maxim command module interface window pops up (figure 2) and includes a 2-wire interface tab that allows for execu- tion of simple i 2 c/smbus commands. the smbus edit boxes in the command (smbus protocols, raw block read/write, eepromread/write) group box accept numeric data in binary, decimal, or hexadecimal. hexadecimal numbers shouldbe prefixed by $ or 0x. binary numbers must be exactly eight digits. see figure 2 for an illustration of this tool. detailed description of hardware the max17061a ev system (MAX17061AEVCMAXQU+)consists of the max17061a ev kit (max17061aevkit+) and the maxim cmaxqusb+ command module. the ev kit evaluates the max17061a wled driver and thecmaxqusb+ provides the i 2 c/smbus-compatible inter- face for software control of the led brightness in 256steps, backlight-controller operating mode, manufacturer and silicon revision detection, and fault detection. the max17061a ev kit is powered from a 5.5v to 24v dc supply at vin and a 4.5v to 5.5v dc supply at vcc. led current can be configured to provide a fixed 25ma or adjustable 15ma to 30ma full-scale led current through jumper ju11 and/or resistor r5. the max17061a ev kit utilizes a step-up dc-dc con- verter to generate the voltage required to drive up to eight strings of 10 surface-mount wleds. as shipped, the max17061a ev kit is configured for evaluation with four strings of 10 wleds. evaluate: max17061a max17061a evaluation kit/evaluation system _______________________________________________________________________________________ 5 figure 2. interface diagnostic window downloaded from: http:///
evaluate: max17061a white led string configuration as configured, the max17061a ev kit is assembledwith four strings of 10 wleds (string 1?tring 4), but can be reconfigured to drive up to eight strings of 10 wleds. each string has an associated 3-pin header (ju1?u8) and feedback pin (fb1?b8). to evaluate additional strings (string 5?tring 8), the ev kit must be reconfigured as follows: 1) populate string_ with either the wled listed in the component list , or its equivalent. 2) cut the trace (solder side) between pins 2-3 of the string? associated header-footprint (ju5?u8). 3) install a 3-pin header (ju5?u8) and configure its shunt according to table 2. to evaluate the ev kit with off-board wled strings, seethe off-board white led string configuration section. off-board white led string configuration the max17061a ev kit can also be used to drive off-board wled strings. to evaluate external wled strings, remove the shunts from jumpers ju1?u8. see table 2 for jumpers ju1?u8 configuration and table 3 for jumper ju9 configuration. removing these jumpers effectively disconnects the on-board wled stringsbetween the output and feedback pins, allowing the connection of external wled strings. for each external wled string, connect the cathode terminal of the string to the corresponding feedback pad (fb1?b8) and connect the anode terminal of the string to the vout pad. once the external wled strings are connected between the vout pad and the fb_ pins, the ev kit can be evaluated in the same manner as the on-board wled strings. evaluating more than 10 wleds per string may require component changes. refer to the max17061a ic data sheet for component selections. led string capacitance in some lcd panel applications, a 0.1? (typ) capacitor(c led ) is placed in parallel with each led string to improve esd immunity. as such, the max17061a evkit provides a footprint across each led string in addi- tion to footprints for pullup resistors on each fb_ pin. refer to the lcd panel capacitance section in the max17061a ic data sheet for more detailed information. setting full-scale led current (i led(fs) ) the full-scale current through each wled string is con-figured by connecting the iset pin (pin 24) to vcc or connecting it to gnd through resistors r4 and r5. when iset is connected to vcc, the full-scale current per string is set to 25ma; when pulled to gnd, the full- scale current per string is adjustable from 15ma to 30ma: where r4 is a 130k resistor and r5 is a 200k poten- tiometer. the iset pin is configured through jumper i k rr ma led fs () = + ? ? ? ? ? ? 20 200 45 max17061a evaluation kit/evaluation system 6 _______________________________________________________________________________________ table 2. jumper ju1?u8 function shunt position fb_ pin string_ 1-2 connected to cathode of wled string enabled 2-3 connected to vcc disabled not installed connect to an external wled string on-board wled string not used table 3. jumper ju9 function shunt position vout installed* c onnected to anod es of on- b oar d wle d str i ng s not installed connect to anodes of off-board wled strings * default position. table 4. jumper ju11 function shunt position iset pin i led(fs) 1-2 connected to vcc 25ma 2-3* connected to gnd through r4 and r5 adjustable from 15ma to 30ma * default position. downloaded from: http:///
ju11. see table 4 for jumper ju11 settings. switching-frequency selection (osc) the max17061a ev kit is configured to operate at1mhz, but provides the option to set the switching fre- quency of the step-up dc-dc converter to 500khz or 750khz. the switching frequency is set by configuring ju13 to the shunt position, as shown in table 5. changing the switching frequency could require differ- ent converter components (refer to the max17061a icdata sheet for proper component selections). setting dpwm frequency (f dpwm ) the max17061a uses an internal dpwm signal to performdimming control. the dpwm frequency is specified by an external resistor, connected from the fset pin to gnd: where = 10.638, = 5.5, = 58509. the adjustable range for the fset resistor (rfset) isfrom 64k to 465k , corresponding to the dpwm fre- quency of 1350hz to 200hz. rfset consists of resis-tors r6 and r7 on the ev kit, where r6 is a 41.2k resistor and r7 is a 500k potentiometer. if making adjustments, note that the minimum usable frequencyresults from a maximum resistance of 465k . fh z rfset rfset dpwm [] = + = + 10 1000 10 99 | evaluate: max17061a max17061a evaluation kit/evaluation system _______________________________________________________________________________________ 7 table 5. jumper ju13 function shunt position osc pin operating frequency 1-2* connected to vcc 1mhz 2-3 connected to gnd 500khz not installed unconnected 750khz * default position. downloaded from: http:///
evaluate: max17061a max17061a evaluation kit/evaluation system 8 _______________________________________________________________________________________ figure 3. max17061a ev kit schematic downloaded from: http:///
evaluate: max17061a max17061a evaluation kit/evaluation system _______________________________________________________________________________________ 9 figure 4. max17061a ev kit component placement guide?omponent side downloaded from: http:///
evaluate: max17061a max17061a evaluation kit/evaluation system 10 ______________________________________________________________________________________ figure 5. max17061a ev kit pcb layout?omponent side downloaded from: http:///
maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a maxim product. no circuit patent licenses are implied. maxim reserves the right to change the circuitry and specifications without notice at any time. maxim integrated products, 120 san gabriel drive, sunnyvale, ca 94086 408-737-7600 ____________________ 11 2009 maxim integrated products maxim is a registered trademark of maxim integrated products, inc. evaluate: max17061a max17061 evaluation kit/evaluation system figure 6. max17061a ev kit pcb layout?older side downloaded from: http:///

▲Up To Search▲

Price & Availability of MAX17061AEVCMAXQU

	To Download MAX17061AEVCMAXQU Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .